iNAV 31K G2  AdvancedTCA AMC Carrier Card for 4 mid-size AMCs

iNAV 31K G2 ATCA Carrier Card for AMC Modules

iNAV 31K G2 ATCA Block Diagram

ATCA AMC Carrier Card with 24 GbE and two 10GbE Ports
The Interphase iNAV 31K G2 offers four mid size AMC bays and support for Rear Transition Module (RTM). The bay B4 can support a processor AMC which can work with the optional PCI Express and control the SAS/SATA disk installed in bay B4.

The 24 Gigabit and two 10GbE Port LAN switch provide four Gigabit links for each AMC bay and two Base Interface links, Fabric Interface links, Board Computer Management (BMC) links and opt. RTM. The ATCA 3.1 Fabric Interface support two 10GbE or Gigabit Ethernet links. Line rate switching is possible with IPv6 support, VLAN support, advanced QoS, link aggregation, port mirroring and many other features.

The BMC consists of a PowerPC 8347E with 667 MHz, up to 1 GB DDR RAM and Gigabit connections to the local Ethernet switch. Telecom clock management provides the ability to accept a synchronization clock from any AMC bay or the backplane, and to drive a clock to any combination of AMC bays. Full local and remote management is provided through the BMC. The IPM controller is compliant with ATCA 3.0, ATCA 3.1 and AMC specifications.

The optional PCIe x4 switch allows AMC.1 connections to each AMC bay, the RTM and the BMC. The PCI Express switch is controlled by either the BMC or AMC bay B4.

At the optional RTM the AMC ports 13-15 and 17-20 from AMC bays B1 through B4 are routed to the connector. The opt. x4 PCI Express link support RTM management and Telecom clock I/O and IPM controller connections.

The iNAV 31K G2 includes a rich Software suite for the BMC and a fully featured firmware package for the IPM controller. Boot monitor, Wind River PNE Linux driver support and full IP services including DHCP and FTP are possible. A Command Line Interface and SNMP allows a flexible configuration and management. Layer 2 switching functionality support and Layer 3 routing with RIP v1/v2, OSPFv2 and wire speed routing is available.

Product Specification
	ATCA 3.1 compliant carrier card with mid size AMC links and Rear Transition module support
	24 port Gigabit Ethernet and 2 port 10GbE LAN switch:
	-	Four AMC.2 Gigabit links for each AMC bay
	-	Two Base Interface links
	-	Board Management Computer links
	-	Optionally Rear Transition module links
	-	Two 10Gigabit or Gigabit ATCA 3.1 Fabric ports
	-	Line rate switching
	Optionally PCIe x4 switch:
	-	Link to each AMC bay compliant with AMC.1, RTM and BMC
	-	Processor AMC is configurable to be either the BMC or AMC B4 bay
	Board Management Computer consists of 667 MHz PowerPC 8347E with up to 1 GB DDR RAM and Gigabit connections to the Ethernet switch
	Up to 512 MB Flash
	Telecom clock management
	Optionally Rear Transition module support
	251W power distribution limit with max. load
	0..55°C operating temperature range
	2 years warranty

	Ordering Information
	iNAV 31K-001	ATCA AMC Carrier Card
	iNAV 31K-002	ATCA AMC Carrier Card with PCIe
	iNAV 31K-003	ATCA AMC Carrier Card with RTM Support
	iNAV 31K-004	ATCA AMC Carrier Card with RTM Support and PCIe
	iNAV 31K-Doc	User's Manual

powerBridge Computer Vertriebs GmbH

Ehlbeek 15a • 30938 Burgwedel • Germany
Tel: +49-5139-9980-0 • Fax: +49-5139-9980-49

Copyright 2011 by powerBridge Computer • Questions or comments to: info@powerbridge.de