|
TIP903 3
Channel Extended
CAN Controller with CAN High-Speed Interface
TIP903 Block Diagram
IOP308-3 Transition Module with DB-50 Connectors and 6U/4HP EMC Front
Panel
for 1..3 IP Modules
IOP402A Transition Module with 50 Phoenix Combicon Screw Terminals, RF Filtered
|
|
40m Bus length at 1Mbit/s Data Rate
The TIP903 IndustryPack module is a threefold
extended CAN bus interface with Intel 82527 CAN controllers. The 82527
controller supports the CAN specification 2.0 part A and B.
The
TIP903 IP module is equipped with CAN high-speed interfaces according ISO 11898.
At a bit rate of 1Mbit/s is a max. 40m
bus length possible. Up to 110 participants may be connected at a bus
line. An on-board termination may be switched off for each channel via jumper.
An extensive scope of drivers is available: Linux, LynxOS, OS-9, pSOS+,
VxWorks and Windows NT/2000/XP. The drivers are delivered as a C source
code - except the Windows driver.
|
|
|
Product Specification
|
|
|
Type 1 IndustryPack module,
single-size, 8MHz clock
|
|
|
3 port extended CAN controller, supports
CAN specification 2.0, part A and B
|
|
|
CAN high-speed interface, ISO 11898, three
82C250 CAN bus driver
|
|
|
3 Intel 82527 controller
|
|
|
Transfer rate up to 1Mbit/s at a max. of 40m bus length
|
|
|
Max. 110 CAN knots for each bus line
|
|
|
On-board 120 Ohm termination, switching off via jumper
|
|
|
Linux, LynxOS, OS-9, pSOS+, QNX, VxWorks and
Windows NT/2000/XP drivers are available
|
|
|
0..70°C operating temperature range
|
|
|
5 years warranty
|
|
|
|
|
Ordering Information
|
 |
|
|
TIP903-10
|
3 port ext. CAN controller IP module
|
|
|
|
TIP903-ED
|
Engineering Documentation
|
|
|
|
IOP305-3/903
|
Transition module 6U/4HP with three DB-9 connectors
|
|
IOP305-6/903
|
Transition module 6U/4HP with three DB-9 connectors
|
|
IOP308-1
|
Transition module 6U/4HP with a DB-50 connector for one IP module
|
|
IOP308-2
|
Transition module 6U/4HP with four DB25 connectors for two IP modules
|
|
IOP308-3
|
Transition module 6U/4HP with three DB25 connectors for three IP modules
|
|
IOP311-1
|
Transition module 6U/4HP with a DB-50 connector and 3MHz RF-filters for
one
IP module
|
|
IOP311-2
|
Transition module 6U/4HP with two DB-50 connectors and 3MHz RF-filters for
two IP modules
|
|
IOP311-3
|
Transition module 6U/4HP with three DB-50 connectors and 3MHz RF-filters for
three IP modules
|
|
IOP402A
|
Transition module 6U/4HP with 50 screw/plug connectors and RF-filters (3MHz) for
one IP module
|
|
|
|
TIP903-SW-12
|
OS-9 driver for TIP903
|
|
|
TIP903-SW-32
|
pSOS+ driver for TIP903
|
|
|
TIP903-SW-42
|
VxWorks driver for TIP903
|
|
|
TIP903-SW-62
|
Windows NT 4.0 driver for TIP903 *
|
|
|
TIP903-SW-65
|
Windows WDM driver for TIP903 *
|
|
|
TIP903-SW-72
|
LynxOS driver for TIP903
|
|
|
TIP903-SW-82
|
Linux driver for TIP903
|
|
|
TIP903-SW-92
|
QNX4 driver for TIP903
|
|
|
TIP903-SW-95
|
QNX6 driver for TIP903
|
|
|
|
TIP903-DOC
|
TIP903 3 Channel Extended CAN Bus IP User Manual |
|
* Windows Driver Support at the Use with PCI Carrier Boards only in
conjunction with TEWS IP
Carrier Boards
|
